Frequently Asked Questions
The main causes of failure in a transformer result from a compromise of the internal insulation. This results from the cumulative effects of aging, mechanical damage or, in some circumstances, design or manufacturing faults. Insulation within most transformers is essentially paper impregnated with oil. This insulation can be compromised during the transformers life by mechanical stress (vibration) or certain aging processes degrading the paper and the oil. These processes are well understood by Aurtra.
If the water content in the transformer oil is within the IEEE standard specified limits, then, we can be comfortable with its operating condition. Violating the standard limits may result in fault conditions. The same applies for temperature measurements.
TILAS provides the exact data for temperature as well as water content in oil and hence indicates normal or risky operating conditions.
An increasing trend in the temperature and water activity of a transformer shows its unhealthy condition. Therefore, if the situation persists, the owner should plan maintenance or replacement.
As the level of moisture content increases in a transformer it has two major effects. Firstly, the additional water interacts with the paper in the insulation causing accelerated damage. This damage weakens the mechanical strength of the paper, allowing cracks to form and breakdowns to occur. Secondly, the additional water interferes with the insulation performance of the oil impregnated paper. Under certain circumstances this can result in insulation breakdown and catastrophic damage. Therefore, a high value of moisture in the transformer oil indicates an unsafe operating state. Such transformers must be managed very carefully and typically cannot be used to their original design limits safely.
Transformers do not perfectly convert power. Some energy is lost in the process. This energy heats the transformer. As the temperature rises it causes changes within the transformer which degrade performance. All transformers have a maximum safe operating temperature. They also have a maximum safe rate of temperature change under high instantaneous load conditions.
Yes, to some degree. However, similar to all electrical equipment, the temperature deep inside the transformer will be much higher than that observed at the surface (or tank) due to cooling of the surface by ambient air.
Not necessarily. It depends on the application and the cost benefit to be realized. Higher temperature class insulation systems cost more and larger transformers are more expensive to build. Therefore, the more expensive insulation systems are more likely to be found in the larger KVA units.
Insulation class was the original method used to distinguish insulating materials operating at different temperature levels. Letters were used for different designations.
Oxygen and water both have a substantial impact on the life of the insulation. These oil pollutants interact to breakdown the polymer chains of the insulation paper. As these chains get smaller the paper becomes brittle and cracks occur. Breakdown can occur in these cracks resulting in catastrophic damage.
The transformers installed at high altitudes increase temperature earlier because of the lesser cooling capacity of air due to its lower density. Therefore, it is necessary to continuously monitor the temperature of transformers at high altitudes.
When the transformer is turned on, the magnitude of the current flow is several times the rated full load current. This high magnitude of current during the transformer turn on process is called inrush current.
The data and trends observed using TILAS indicate the risk of failure in the future. Alerts are also triggered when critical limits are breached to enable the engineer to take action to avoid catastrophic failure.
The Aurtra TILAS solution is an advanced tool which provides the health status of a transformer in an easily accessible format. This information will enable Asset Managers to extend the life of aging transformer assets by determining the risks of increasing load or continuing to operate a transformer, as well as making informed decisions on when to refurbish, which maintenance strategy to apply, and when to replace.
The measurements, trends and alarms provided by TILAS include moisture in oil levels, moisture in insulation (hotspot and averaged), depolarization estimates over time, percentage transformer life lost through depolarization, dynamic response of insulation water content and the absolute depolarization level of insulation (hotspot and averaged).
Yes, all data from the date of TILAS installation can be accessed.
In case of non-functioning of TILAS, AURTRA will assist through online troubleshooting. If a fault is diagnosed, a replacement unit will be provided at no cost for subscribers.
No, it will not require any training as the outcome obtained by processed data can be easily understood by engineering staff. Online help is also available. In addition, Aurtra can provide recommendations for any unusual situations to further assist decision-making.
The technology was built upon a foundation of over a decade of research conducted by University of Queensland researchers. It is based on peer-reviewed research and is verified by testing and data gathered from a large number of transformers.
The intelligence obtained from TILAS can be used to plan optimum maintenance of transformers which will certainly increase transformer life.
The TILAS probe is inserted in the oil through an opening in the transformer tank or through a fill valve at the top of the tank. The installation usually takes less than 30 minutes to complete.
Aurtra develops world best practice asset management solutions for power distribution companies globally. Our technology is built on a foundation of over 10 years of research at the University of Queensland in close co-operation with a number of the largest Australian power distribution companies using decades of transformer data.more about us
Register for updates
TILAS Transformer Condition Monitoring
The Aurtra TILAS solution provides cost-effective online transformer condition monitoring for distribution transformer assets of all sizes for a low monthly fee with no lock-in contracts.
Our solutions are low cost, light touch, secure and interoperate with existing tools to extend asset life through improved risk management and optimisation of transformer loading, maintenance and replacement. TILAS provides configurable real time alerts of unexpected status changes, together with graphical short and long term trendsLearn More About Our Solutions
Our world first patented technology
Our patented IP built upon decades of industry data uses advanced predictive analysis to provide actionable reporting and alerts, not just streams of data. Aurtra TILAS solution architecture is fully secure, redundant and responsive with asset data security and protection.Learn More About Our Technology